Skip to content
New product 12 V 100 Ah sodium-ion truck starting battery, 1500 CCA, Group 31T See the launch →

Forklift Battery — Sodium-ion Replacement for 24 V, 48 V and 80 V Trucks

Home / News and Blog / Forklift Battery — Sodium-ion Replacement for 24 V, 48 V and 80 V Trucks
Forklift Battery — Sodium-ion Replacement for 24 V, 48 V and 80 V Trucks
16 Nov 2026

A forklift battery is bought on two numbers: the shift it has to survive, and the hours it takes to recharge. Sodium changes the second one, which is why it fits multi-shift warehouses better than a straight lead-acid swap.

24 / 48 / 80 Vthe three traction voltages
2 V cellswhat is being replaced in the tray
Ballasta lighter pack needs a counterweight plate
Tray footprintthe constraint that decides everything

Truck brands and the voltages they use

Brand Common series Typical voltage Lead-acid block
Toyota 8FBE, 8FB, Traigo 24 V / 48 V / 80 V 2 V cells in a steel tray
Hyster J, E, S series 36 V / 48 V / 80 V 2 V cells
Crown FC, SC, RC 24 V / 36 V / 48 V 2 V cells
Linde E14–E50, H series 48 V / 80 V 2 V cells
Yale MP, GDP, ERP 48 V / 80 V 2 V cells
Jungheinrich EFG, ETV, EJE 24 V / 48 V / 80 V 2 V cells
Mitsubishi / CAT FB, 2ET 48 V / 80 V 2 V cells
Clark C, GTS, TMX 24 V / 48 V / 80 V 2 V cells
Doosan / Daewoo B, BR, D series 48 V / 80 V 2 V cells
Hangcha / Heli / EP CPD, CPDB 48 V / 80 V 2 V cells

Industrial traction packs are built as 2 V cells in series inside a steel tray, counterweighted to replace the lead they replace. A sodium pack is lighter for the same energy, so the tray needs a ballast plate rather than a straight drop-in — that is a design detail we settle before quoting.

What changes and what stays

Stays Changes
Truck Motor, controller, hydraulics Traction cut-off and gauge behaviour
Tray Steel tray and lid Ballast plate, cell spacers, busbar
Charging Charger location Profile, or the charger itself
Connector DIN / Euro connector Only if the pack spec differs

How to size the pack

1. Shift energy. Measure or estimate the kWh a truck uses per shift. A 2-tonne counterbalance doing mixed work commonly runs 8–15 kWh per shift; a reach truck in a tall rack runs more.

2. Opportunity charging. If the truck charges at breaks, the pack only has to cover the longest unbroken stretch, not the whole shift. That is what lets a smaller pack replace a big lead-acid block.

3. Usable depth. Divide by 0.8 for a sensible design point, then check the pack’s continuous discharge rating against the truck’s hydraulic pump, which draws far more than traction.

Charging and the shift pattern

A lead-acid truck needs a full charge and a cooling period; a sodium pack accepts partial charges through the shift, which is what lets one truck cover two shifts without a battery change. The charger, not the pack, usually sets the limit — a legacy charger with a lead-acid profile will undercharge the pack and the truck will feel slow by mid-shift.

Cold stores

In a freezer warehouse the pack works at −25 °C. Discharge is fine; charging is not, and the cell must be above its charge floor before current is accepted. Charging in a warm bay, or heating the pack, is the practical answer — the BMS enforces the limit either way.

Where a sodium pack is the wrong purchase

Single-shift operations. With a cheap tariff and a calendar-based replacement, the payback on any lithium-family pack is slow.

Very high continuous loads. An 80 V truck on constant heavy duty may favour a purpose-built traction pack over a general-purpose one.

No room for ballast. If the tray cannot take a counterweight plate, a lighter pack changes the truck’s stability envelope and that is the manufacturer’s decision, not ours.

Questions buyers ask

Can I keep the existing charger?

Only if its profile can be reprogrammed to the pack’s voltage window. A fixed lead-acid profile will not terminate correctly.

Will the truck’s display still work?

If it reads voltage, it will be misleading. Most fleet conversions add a shunt or a CAN interface so the operator sees real state of charge.

How much weight do I save?

A 48 V 600 Ah lead-acid traction block weighs well over a tonne. The sodium pack of similar usable energy is a fraction of that, which is why ballast is part of the design.

Can it work in a freezer?

Yes for discharge, with a charge floor. Charging below the cell’s cut-off temperature must be prevented or the pack must be warmed.

Do you supply the connector?

Yes, to the truck’s standard — DIN or Euro on most European fleets. Send the connector type with the enquiry.

Where to go next

Products for this application

Industrial & traction 7 models · specs and sizes 24 V 160 Ah forklift sodium-ion battery — 9S, 4.1 kWh single product · full specification

Have a specification question this article does not answer? Send it with the numbers you already have.

Request a quote

Part of

More guides in this group