Skip to content
New product 12 V 100 Ah sodium-ion truck starting battery, 1500 CCA, Group 31T See the launch →
Home / Electrification
Electrification

Start with the engine you already have

Tell the page what the diesel engine is, and it works out the motor, the pack, the charging and the parts the machine needs — for a truck, a bus, a boat, a tractor or a forklift. You get a requirement list you can send to us for a quote.

Tell us the machine — we size the drive

You do not need to know volts or amp-hours. Give us the diesel engine you are replacing and how hard it works; the page turns that into a motor, a pack, a charger and the parts list for the machine. If your machine is not in the list, or the numbers do not look right, contact us.

Diesel engine power
kW
The type changes the controller, the cooling and the price — we confirm it with you.
Distance per day
km
Gross vehicle weight
kg
Payload you must still carry
kg

Fleet and charger planning

One truck is a pack. Twenty trucks is a depot problem: how much energy per night, how many chargers, and what the site supply has to carry. Change the numbers and watch the site demand move.

Vehicles in the fleet
units
Energy per vehicle per day
kWh
Charging window overnight
h

Does the conversion pay back?

A conversion only happens if the numbers work. Put in your fuel bill, your electricity price and what the conversion costs, and the page works out the yearly saving and the payback. If it does not pay back, we will tell you rather than sell you a pack.

Distance per year
km
Diesel consumption
L/100km
Electricity consumption
kWh/km
Diesel price
USD/L
Electricity price
USD/kWh
Maintenance saved
USD/km
Conversion cost
USD

What every conversion needs

A conversion is a new prime mover, the energy that feeds it, and the controls and safety that keep it legal. These thirteen items are what the machine needs, whatever the platform — boat, car, truck, bus or equipment.

  1. 01
    Battery packThe energy store, sized to the daily duty cycle — cells, enclosure, internal fusing and the frame that carries it.
  2. 02
    Traction motorReplaces the diesel engine — the prime mover. Sized to the original engine power, not to the battery.
  3. 03
    Motor controllerThe motor cannot run straight off the battery — the controller sets the speed and torque.
  4. 04
    Drive interfaceCoupling, reduction gear, adapter plate and shaft — carries the torque into the existing driveline.
  5. 05
    High-voltage distributionContactors, pre-charge, fuses, service disconnect, HV junction box, cable and connectors.
  6. 06
    Battery managementCell monitoring, protection, state of charge — no pack is safe to charge without it.
  7. 07
    ChargingOn-board charger or shore / depot charger, plus the inlet the vehicle will actually meet.
  8. 08
    DC-DC, accessory inverter and auxiliary batteryPack voltage down to 12 or 24 V, and AC for pumps or tools where the vehicle needs it.
  9. 09
    Thermal managementMotor and controller cooling, plus the pack kept inside its temperature window — including heating in cold climates.
  10. 10
    Vehicle control and communicationVCU, electronic throttle and gear signals, CAN bus, display of charge and faults.
  11. 11
    High-voltage safetyInsulation monitoring, interlock loop, equipotential bonding, emergency stop, thermal-runaway detection.
  12. 12
    Mechanical installationMotor mounts, battery frame, anti-vibration pads, centre of gravity and axle load.
  13. 13
    Instruments and controlsCharge gauge, warning lamps, throttle lever or pedal — replaces the fuel gauge and pedal.

The thirteen items are the same function on every platform; the form changes. A boat replaces the axle load with trim and draught, an outboard packs motor, controller and gearbox into one pod, and a stationary pump set drops items 04 and 13 altogether.

Then it depends on the platform

Car or light van
  • Brake vacuum pump or electric booster
  • Electric air-conditioning compressor
  • Electric power steering
  • Regenerative braking blending
Truck or bus
  • Electric air compressor and dryer
  • High-flow steering pump
  • Hydraulic pump / PTO motor
  • 24 V system and telematics
Boat
  • Reduction gearbox and thrust bearing
  • Shaft seal and alignment
  • Sea-water or closed-loop cooling
  • Bilge ventilation and gas detection
  • Class-society approval and fire plan

You may also need this equipment

Beyond the thirteen functions there is the equipment around them. Some of it you will already own, some comes with the machine. Use this as a checklist when you prepare the requirement.

Energy

  • ✔Battery pack (sodium-ion, our own cells)
  • ✔BMS master and slave boards
  • ✔PDU with contactors, pre-charge and fusing
  • ✔MSD, current sensor, HV harness

Traction

  • ✔Traction motor
  • ✔Motor controller / inverter
  • ✔Reducer and shaft adapter
  • ✔Motor cooling circuit

Charging

  • ✔On-board charger 6 / 13 / 20 kW
  • ✔Charge inlet — CCS2, GB/T or NACS
  • ✔Depot charger and cable management
  • ✔Charge scheduling with the BMS

Low-voltage

  • ✔DC-DC 2.5 / 6 kW — HV to 12 / 24 V
  • ✔Auxiliary battery
  • ✔Low-voltage fuse box

Thermal

  • ✔Battery chiller / BTMS
  • ✔Coolant pump, radiator, fan
  • ✔PTC heater for the pack and the cab

Steering & brakes

  • ✔Electric steering pump
  • ✔Electric air compressor and dryer
  • ✔Regenerative braking blending
  • ✔EBS / ABS interface

Auxiliaries

  • ✔AC compressor
  • ✔Electric water pump
  • ✔Hydraulic pump or PTO motor
  • ✔Cab heater and fan

Control

  • ✔VCU — vehicle control unit
  • ✔CAN gateway and harness
  • ✔Throttle, brake and gear inputs
  • ✔Display, telematics, diagnostics

Safety & compliance

  • ✔Insulation monitoring (IMD)
  • ✔HV interlock loop (HVIL)
  • ✔Thermal runaway detection and suppression
  • ✔EMC filtering, grounding, homologation support

Ready-made starting points

If the calculator is too open-ended, start from a package. These are reference builds for the most common conversions — the configurator opens with the numbers filled in and you change what does not fit your route.

Light delivery truck 4.5 – 7.5 t

Battery120 kWh · 400 V
Motor150 kW
Charging22 kW on-board
Rest of kitDC-DC 400 → 24 V · 8 kW chiller
Typical range180 – 220 km urban duty
Start from this package →

Rigid truck 12 – 18 t

Battery250 kWh · 600 V
Motor250 kW
Charging2 × 22 kW on-board
Rest of kitDC-DC 600 → 24 V · 10/24 kW BTMS
Typical range200 – 260 km
Start from this package →

City bus 10.5 – 12 m

Battery330 kWh · 600 V
Motor350 kW
Charging2 × 22 kW or 150 kW depot
Rest of kitDC-DC 600 → 24 V · 10/24 kW BTMS
Typical range220 – 280 km per charge
Start from this package →

Coach 12 – 13 m

Battery500 kWh · 800 V
Motor400 kW
Charging2 × 22 kW or 250 kW depot
Rest of kitDC-DC 800 → 24 V · 10/24 kW BTMS
Typical range300 – 380 km
Start from this package →

These are reference sizes for the vehicle class, not a quotation. Range assumes the duty cycle stated and a 90% usable window; both are confirmed after the route survey.

The five systems around the pack

Battery thermal management

  • Chillers 5 / 7 kW
  • BTMS 8/18 kW and 10/24 kW
  • Coolant pumps and heater

Keeps the pack in its temperature window under load — the difference between 3,000 and 6,000 cycles.

Power distribution

  • PDU with contactors and pre-charge
  • Fuses and breakers
  • HV junction box

Puts the high-voltage bus, the pre-charge and the isolation in one place instead of a loom of cables.

Charging

  • On-board charger 6 / 13 / 20 kW
  • Off-board charger
  • Charge inlet and cabling

Sized to the pack voltage and the charge window the vehicle actually has.

Accessory drives

  • Electric steering pump 2.4 / 3 / 4 kW
  • Air compressor 3.7 kW
  • AC compressor 3 kW

Replaces everything the diesel engine used to turn: steering, brakes, air and cabin cooling.

DC-DC and heating

  • DC-DC 2.5 / 6 kW — 350–800 V to 12 / 24 V
  • PTC water heater 5 / 7 / 12 kW

Feeds the original 12/24 V loads and the cabin heat without a second battery system.

What matches which pack

PackTypical useChargerDC-DC
48 – 51.2 VForklift, AGV, golf, small boat6 kW OBC48 → 12 V
64 – 76.8 VTwo-wheeler, light truck, RIB13 kW OBC72 → 12 / 24 V
96 – 110 VVan, minibus, inboard boat13 – 20 kW OBC96 → 24 V
400 – 800 VTruck, bus, fast-charge boat20 kW OBC or off-board600 → 24 V

Ratings are matched to the pack you configure — send the vehicle details and we return the list with the pack.

Projects we take on

Fleet conversion — truck & bus

100 – 800 kWh per vehicle

Pack, PDU, charger and thermal in one kit; pilot vehicle first, then the fleet.

Marine propulsion

Inboard shaft line or outboard pod

48 – 800 V packs, DC link sized with the motor controller, sealed to IP67.

Port and terminal equipment

RTG, reach stacker, STS crane

High-current packs with opportunity charging between moves.

Mining and off-highway

Haul truck, LHD, drill rig

Heavy-duty pack frames, vibration and dust protection, remote monitoring.

Grid-scale storage

0.5 – 5 MWh container

The 500 kVA / 1028 kWh container we already build, plus PCS and fire suppression.

Microgrid — solar / wind / diesel hybrid

100 kWh – 1 MWh

Sodium-ion bank with hybrid inverter, sized for daily cycling.

Start from the battery

Configure the pack first, then add the systems around it. Both configurators take you straight to a quotation.

Two questions before you size a conversion

How big a pack does a diesel engine need?

Size the motor from the engine (about 0.95 of rated kW), then size the pack from the energy the duty needs — daily kilometres for road machines, hours between charges for everything else.

What has to match between the pack and the parts around it?

Three things cause most delays: the voltage window, the CAN protocol and the connector type — check them before ordering any part.

Still deciding?

Moving a fleet or a machine off petrol? Send the duty cycle and we will size the pack and the charger before you commit to hardware.

Request a quote

Sized the drive? Take the same numbers into the tools — they do the pack, the layout and the heat.