Skip to content
New product 12 V 100 Ah sodium-ion truck starting battery, 1500 CCA, Group 31T See the launch →

The Three Cathode Chemistries: Layered Oxide vs. NFPP vs. Prussian Blue

Home / News and Blog / The Three Cathode Chemistries: Layered Oxide vs. NFPP vs. Prussian Blue
The Three Cathode Chemistries: Layered Oxide vs. NFPP vs. Prussian Blue
15 Nov 2026

Ask “which sodium cathode is best” and you get a different answer depending on who is asking. The cathode sets the voltage curve, the cycle life and the cost, and those three trade against each other. So the honest answer starts with who you are.

The three families in one table

Layered oxide NFPP (polyanion) Prussian blue
Energy density highest lowest middle
Voltage curve sloped, higher average flat plateau sloped, moderate
Cycle life 3,000–5,000 up to ~10,000 2,000–4,000
Cost pressure nickel content iron, cheap very cheap
Handling moisture sensitive forgiving water in the lattice is the risk

If you are the factory

You care about yield and line stability before you care about Wh/kg. NFPP is the easiest to run: a flat charge curve means the formation step is predictable, and the cell tolerates minor process drift. Layered oxide gives you the headline energy number but punishes humidity in the dry room and shows up as scrap.

The question to ask is not which cathode is better but how many cathode suppliers you can qualify. One source is a single point of failure, whatever the chemistry.

If you are the trader

Your risk is documentation and consistency, not electrochemistry. Buy the family that a factory will support with a stable datasheet for two years, because your customer will compare the second shipment against the first.

Prussian blue is tempting on price and awkward on claims: water content and vacancy defects vary by supplier, and the cycle numbers move accordingly. If you cannot test, buy the family with the flattest variance.

If you are the end user

You care about the duty cycle. Daily deep cycling in a fixed installation points to NFPP. A weight-limited vehicle points to layered oxide and its energy density. A cost-first, short-life application — a backup block that rarely cycles — can use Prussian blue without regret.

Cold performance is not decided by the cathode alone. Ask for the capacity-at-temperature curve of the exact model rather than reasoning from the family name.

What we would say in a meeting

Pick the cathode that matches the failure mode you can least afford: scrap in the factory, variance for the trader, or a pack that fades before the asset is paid off.

Send the duty cycle and we will tell you which of the three we would quote — and which one we would avoid for your case.

What the numbers look like across the family

Cycle claims move with the cell, not only the cathode. In the same product range: a 0.9 Ah high-rate cylindrical cell reaches 1,000 cycles to 85% at 1C; a 7 Ah pouch reaches 2,000 at 0.5C with a 1 N·m stack torque; an 18 Ah cylindrical reaches 3,000; a 55 Ah prismatic reaches 4,000 at 0.5C. Voltage separates the families just as clearly: a low-temperature 50 Ah cell is specified at 2.85 V, while the standard product of the same format sits at 3.0 V.

One more data point

The same 18650 format spans 850 mAh and 900 mAh cells with 1,000-cycle quotes and a 1,300 mAh cell charged to 4.0 V — three different designs in one case size. Format tells you nothing about the cathode; the voltage window and the cycle claim do.

Where to go next

Questions we get asked about this

Which cathode gives the longest life?

Polyanion NFPP cells are usually quoted for the longest cycle life, up to around 10,000 cycles at moderate depth, at the cost of energy density.

Which gives the highest energy density?

Layered oxides, typically 20–30% more Wh/kg than NFPP in the same format.

Is Prussian blue a bad choice?

It is a cost-first choice. Reasonable for backup and moderate-cycle duty, weaker for a project whose economics depend on ten years of daily cycling.

Products for this application

Sodium-ion Batteries 62 models · specs and sizes 10145138 Sodium-ion Cell, 10 Ah, Pouch single product · full specification

Have a specification question this article does not answer? Send it with the numbers you already have.

Request a quote

Part of

More guides in this group