Skip to content
New product 12 V 100 Ah sodium-ion truck starting battery, 1500 CCA, Group 31T See the launch →

48V Golf Cart Battery — Sodium-ion Replacement Packs

Home / News and Blog / 48V Golf Cart Battery — Sodium-ion Replacement Packs
48V Golf Cart Battery — Sodium-ion Replacement Packs
16 Nov 2026

A 48 V sodium-ion pack that drops into the tray where four 12 V or six 8 V lead-acid blocks used to sit. The motor, controller and cart stay; the pack, the charge profile and the low-voltage cut-off change. This page covers what fits, how to size it, what the install actually involves, and where the chemistry is the wrong purchase.

48 Vnominal, 4×12 V or 6×8 V replacement
50–280 Ah2.4 to 13.4 kWh nominal
−40 °Cdischarge; charging needs a warm pack
1 chargermust be replaced or reprogrammed

Which carts this fits

Brand coverage matters because buyers search the cart they own, not a voltage. The table lists the families we quote for most often; where a model is not listed, a photograph of the tray and the controller label is enough for us to check.

Brand Common models Nominal voltage Original layout
Club Car DS, Precedent, Onward, Tempo, Carryall 48 V (older DS 36 V) 4 × 12 V or 6 × 8 V
EZGO TXT, RXV, Freedom, Express 48 V (some TXT 36 V) 4 × 12 V or 6 × 8 V
Yamaha G22, G29 Drive, Drive2, Concierge 48 V 4 × 12 V
ICON i20, i40, i60, i80 48 V 4 × 12 V, often factory lithium
Denago Rover, Nomad, Summit 48 V Factory lithium, 48 V
Evolution Classic, Forester, Carrier 48 V 4 × 12 V or factory lithium
Star EV Sirius, Capella 48 V 4 × 12 V
Advanced EV (ADV) 1.0, 2.0, 4.0 48 V Factory lithium
Bintelli Beyond, Nemesis 48 V 4 × 12 V or lithium
Tomberlin E-Merge, Vanish 48 V 4 × 12 V
Garia Via, Monaco, Golf 48 V Factory lithium
Cushman / Textron Hauler, Shuttle 48 V 4 × 12 V or 6 × 8 V
Taylor-Dunn Burden carrier, tug 48 V / 72 V Industrial lead-acid
Epic / Zone / Kandi Various imported carts 48 V / 60 V / 72 V Mostly factory lithium

Two cautions. First, a cart with a factory lithium pack is not a lead-acid replacement job — the BMS talks to the cart, and swapping in a different pack means solving the communication, not just the voltage. Second, a 36 V cart stays 36 V; the controller and motor are matched to it.

What changes and what stays

Stays Changes
Drivetrain Motor, controller, loom Low-voltage cut-off setting
Energy — Pack and BMS
Charging — Charger profile, or the charger itself
Dashboard Key switch, lights Battery gauge if it reads voltage
Mechanical Tray and hold-down Weight distribution, sometimes a spacer

The weight difference is the part owners notice first: a 48 V lead-acid set of four 12 V blocks can weigh over 100 kg, and the sodium pack that replaces it is a fraction of that. On a small cart that changes ride height slightly and can change stability at speed — worth checking before the first drive.

How to size the pack

Range follows usable energy, not the Ah on the label. Three steps:

1. Estimate daily energy. A golf cart uses roughly 0.06–0.10 kWh per km on flat ground, more on hills and with passengers. A 15 km round of golf is therefore about 1–1.5 kWh at the wheel.

2. Convert to pack energy. Divide by drivetrain efficiency (about 0.85) and by usable depth of discharge (0.8 is a sensible design point): 1.5 kWh ÷ 0.85 ÷ 0.8 ≈ 2.2 kWh of nominal pack.

3. Match to the shelf. A 48 V 50 Ah pack holds 2.4 kWh nominal; a 48 V 100 Ah pack holds 4.8 kWh. If the cart does two rounds a day or lives on hills, take the larger one — the cost difference is smaller than a second charger.

What the install involves

Step 1 — Photograph the tray with a tape measure in frame, and note the controller label. Tray depth, terminal positions and the hold-down are what decide fitment.

Step 2 — Isolate and remove the lead-acid blocks. Label the main positive and negative before disconnecting; reversing them is the one mistake that destroys a controller.

Step 3 — Set the low-voltage cut-off in the controller or rely on the BMS. A controller set for lead-acid reads a sodium pack as empty while it still has useful charge, which shows up as reduced range rather than a fault.

Step 4 — Fit the pack and torque the terminals. Re-check torque after the first week of use; a loose terminal becomes a hot joint.

Step 5 — Replace or reprogram the charger. This is the step most swaps fail on. A lead-acid charger runs a three-stage profile and will either undercharge a sodium pack or hold it at a voltage it should not sit at. A programmable charger set to the pack’s window is the practical answer.

Charging settings that matter

Three numbers decide whether the pack lives a long life: the charge cut-off voltage, the charge current, and the temperature floor below which charging must stop. The first two come from the pack specification; the third is a cell property and cannot be overridden by software. In freezing weather the pack will discharge normally and refuse to charge until it warms — that is protection, not a fault.

Where this is not the right answer

A 36 V cart. The controller and motor are matched to 36 V; a 48 V pack is the wrong purchase.

A cheap, short-season cart. If the existing lead-acid set is replaced every three years on a mild-climate course and power is cheap, the payback on any lithium-family pack is slow.

An unusual tray. A standard pack will not fit every cart, and a bracket is not always enough. Where the tray is non-standard, the honest answer is a custom build.

Questions buyers ask

Will my lead-acid charger work?

Usually not without reprogramming. It needs to reach the pack’s full-charge voltage and then stop; a lead-acid profile will either undercharge or hold the pack at a voltage it should not sit at.

Can I keep the cart’s battery gauge?

Only if it reads state of charge from a protocol the new BMS supports. Most lead-acid gauges read voltage, which is misleading on a sodium pack — a shunt or CAN-based gauge is the reliable option.

How much range do I get?

Range follows usable kWh. A 48 V 100 Ah pack holds 4.8 kWh nominal and about 3.8 kWh usable at 80% depth of discharge — compare that with the lead-acid set at its own usable depth, not its nameplate.

Does the motor need changing?

No, if the voltage stays the same. A 36 V to 48 V conversion changes the controller and often the motor, and is a different project.

Do you cover carts that came with a factory lithium pack?

Yes, with a different answer. The pack has to speak the cart’s protocol, so we ask for the controller label and the existing BMS wiring before quoting.

What if my model is not listed?

Send a photo of the tray with a tape measure in frame and the controller label. That is enough to check fitment without guessing at a size.

Where to go next

Products for this application

EV packs 22 models · specs and sizes 4850 — 48 V 50 Ah sodium-ion pack single product · full specification

Have a specification question this article does not answer? Send it with the numbers you already have.

Request a quote

Part of

More guides in this group