Skip to content
New product 12 V 100 Ah sodium-ion truck starting battery, 1500 CCA, Group 31T See the launch →
Home / Products / Components / Electrode Sheets / Hard carbon coated aluminium electrode sheet — 241 × 200 mm
Hard carbon coated aluminium electrode sheet — 241 × 200 mm

Hard carbon coated aluminium electrode sheet — 241 × 200 mm

Brand: Polytone
Part number: PT-ES-HC-AL241
Voltage window: 0.005 – 2.0 V
Specific capacity: 280 ± 30 mAh/g
Sheet size: 241 × 200 mm
Availability: In stock
Price on request — quoted per configuration, quantity and Incoterm.Ask for a price →

Hard carbon coated on aluminium foil, supplied as ready-to-punch electrode sheets so a lab can go from foil to coin cell without a coating line.

Working window: 0.005 – 2.0 V vs Na/Na⁺ — this is the negative electrode side; pair it with a cathode sheet and a NaPF6 electrolyte.

How to use

  1. Cutting: punch 12 mm or 14 mm discs for coin cells.
  2. Weighing: active mass = electrode mass (mg) − disc area (cm²) × foil surface density (4.22 mg/cm²) × active ratio (92%).
  3. Drying: vacuum oven at 60–80 °C for 2–4 hours before assembly.
  4. Assembly (glove box): negative case → sodium chip → electrolyte → separator → electrolyte → electrode sheet → spacer/ring → spring → positive case.
  5. Testing: 5 V / 10 mA 8-channel tester; enter the active mass, then set current from the target C-rate (0.1C = nominal capacity mAh/g × active mass mg × 0.001 × 0.1).

Storage: seal the sheet immediately after opening — keep it in a glove box or a 60 °C oven.

Specification

Hard carbon coated aluminium electrode sheet — 241 × 200 mm — specification
Sheet size241 × 200 mm
Coated area241 × 175 mm (12.5 mm margin each side)
CoatingSingle side
Total thickness80 – 100 µm
Foil thickness16 µm
Coating density6.3 ± 0.2 mg/cm²
Foil surface density4.22 mg/cm²
Active material92%
Compacted density0.9 g/cm³
Voltage window0.005 – 2.0 V
Specific capacity280 ± 30 mAh/g
StorageSeal after opening; glove box or 60 °C oven
ApplicationSodium-ion coin-cell research

Ordering: MOQ and lead time

These figures are quoted by order type rather than per part number, because the same cell can ship from stock or start a new tooling project. If your quantity sits between two rows, the smaller one applies until a change is needed.

Minimum order quantity

Sample evaluation 1 unit A single piece, so you can test the chemistry and the fit before committing to a batch.
Standard catalogue item 5–10 units The stocked line: cells, cases and components that need no change before shipping.
New ODM design 100–200 sets New structure, new BMS protocol or new housing tooling. The batch size covers the setup work.
Large project quoted per project Container-scale and framework agreements are quoted against the schedule, not against a unit price.

Production lead time

Stock item 3–5 working days Shipped from stock once the order is confirmed.
OEM (silk print, label, packaging only) 15–20 working days Same structure and same BMS. Only the marking and the packaging change.
New ODM (new structure, BMS protocol, housing, diesel-to-electric) 30–35 working days Counted from specification freeze, not from the enquiry.
Adding a certification +15–30 days On top of the production time above. The laboratory sets the schedule, not us.

Shipping transit is quoted separately and starts after production finishes. We do not publish a transit figure, because it depends on the forwarder, the route and the season — ask for it with the order and we will quote the current rate.

Request a quote Ask an engineer Preview the datasheet

Full A4 datasheet, one page. We store the address to answer you — nothing else.

WhatsApp Request a quote