Skip to content
New product 12 V 100 Ah sodium-ion truck starting battery, 1500 CCA, Group 31T See the launch →
Home / Products / Components / Electrode Sheets / Hard carbon aluminium electrode, 10×10 cm
Hard carbon aluminium electrode, 10×10 cm

Hard carbon aluminium electrode, 10×10 cm

Brand: Polytone
Part number: PT-ES-HC-100
Areal capacity: 1.73 mAh/cm²
Sheet size: 10 × 10 cm
Availability: In stock
Price on request — quoted per configuration, quantity and Incoterm.Ask for a price →

High-capacity hard carbon electrode on 12 µm aluminium foil, cut to 10 × 10 cm for coin-cell and small pouch work. The carbon is milled to 5 µm, which is what gets the reversible capacity up to 307.5 mAh/g without losing the first-cycle efficiency.

Half-cell reference (0.1C, 0.00–2.00 V): 307.5 mAh/g specific discharge capacity, 87.4% first coulombic efficiency.

Areal performance: coating 6.00 mg/cm² ±2%, areal capacity 1.73 mAh/cm² — so a 12 mm disc carries a predictable capacity without re-calibrating your test protocol.

Calendered or not: the standard sheet is supplied at 0.90 g/cm³; a calendered version is available. Uncalendered sheets should be pressed before use if your target density is higher.

Drying before use: vacuum dry at 85–105 °C for 4 hours with two gas exchanges. Weigh each disc and recalculate the areal density from its actual mass before you set the test current.

Shelf life: 6 months in the vacuum-sealed pack; use within 1 month of opening.

Specification

Hard carbon aluminium electrode, 10×10 cm — specification
Sheet size10 × 10 cm
Hard carbon particle size5 µm
Active material95.5%
FoilAluminium, 12 µm, 3.30 mg/cm²
Coating density6.00 mg/cm² (± 2%)
Areal capacity1.73 mAh/cm²
Specific capacity307.5 mAh/g (0.1C, 0.00–2.00 V)
First coulombic efficiency87.4% (half cell)
Compacted density0.90 g/cm³ (calendered version available)
Drying85–105 °C, 4 h, vacuum, two gas exchanges
StorageVacuum sealed 6 months; use within 1 month of opening
ApplicationSodium-ion anode research

Ordering: MOQ and lead time

These figures are quoted by order type rather than per part number, because the same cell can ship from stock or start a new tooling project. If your quantity sits between two rows, the smaller one applies until a change is needed.

Minimum order quantity

Sample evaluation 1 unit A single piece, so you can test the chemistry and the fit before committing to a batch.
Standard catalogue item 5–10 units The stocked line: cells, cases and components that need no change before shipping.
New ODM design 100–200 sets New structure, new BMS protocol or new housing tooling. The batch size covers the setup work.
Large project quoted per project Container-scale and framework agreements are quoted against the schedule, not against a unit price.

Production lead time

Stock item 3–5 working days Shipped from stock once the order is confirmed.
OEM (silk print, label, packaging only) 15–20 working days Same structure and same BMS. Only the marking and the packaging change.
New ODM (new structure, BMS protocol, housing, diesel-to-electric) 30–35 working days Counted from specification freeze, not from the enquiry.
Adding a certification +15–30 days On top of the production time above. The laboratory sets the schedule, not us.

Shipping transit is quoted separately and starts after production finishes. We do not publish a transit figure, because it depends on the forwarder, the route and the season — ask for it with the order and we will quote the current rate.

Request a quote Ask an engineer Preview the datasheet

Full A4 datasheet, one page. We store the address to answer you — nothing else.

WhatsApp Request a quote